REF16-S101-DC24V-10A ETA Electronic circuit breaker
Selective load protection
Electronic cut-off characteristic
Electronic reset input RE
Rated current 10 A
- Buy 10 for €61.68 each and save 5%
- Buy 25 for €56.62 each and save 13%
- Buy 50 for €52.07 each and save 20%
- Buy 100 for €50.55 each and save 22%
Artikel dem Warenkorb hinzufügen oder Alles auswählen
The REF16-S unit expands the product group "electronic overcurrent protection" for DC 24 V applications.
It selectively protects all DC 24 V load circuits with a width of only 12.5 mm. This is achieved by a combination of active electronic current limitation in the event of a short circuit and an overload cut-off at typ. 1.25 x IN. In combination with the E-T-A plug-in bases 80plus and 81plus, the REF16-S
can be mounted quickly, conveniently and flexibly. The bases allow current distribution and signal distribution via pluggable bridges.
In addition, the REF16-S is latched to the base and can be assigned to fixed current ratings or slots with a coding pin. The installation dimensions comply with the DIN 43880 installation device standard.
DC 24 V switched-mode power supplies are used very frequently in automation technology. However, in the event of an overload, they regulate the output voltage that is to supply all connected loads. So if a fault occurs in a single load in the system, the voltage also collapses in all other load circuits. This often results not only in an undefined fault condition, but even in a standstill of the machine or system.
This is exactly where the REF16-S intervenes by reacting to the overload condition faster than the switching power supply. The maximum possible overcurrent is always limited to typically 1.25 times the selected rated current (see Table 1). This makes it possible to switch on capacitive loads up to 20,000 μF, but they are switched off in the event of an overload or short circuit. For adaptation to the load conditions, the rated current is available in fixed values of 0.5 A...10 A. Operating and error states are indicated by a multi-coloured LED, a potential-free signal contact or by an integrated short-circuit-proof status output. Remote actuation is possible via a remote reset signal or a remote ON/OFF control signal. The manual ON/OFF switch directly on the unit allows targeted commissioning of individual load circuits.
As soon as the REF16-S detects overload or short-circuit in its load circuit, it blocks the load output transistor and thus interrupts the current flow in the faulty circuit. Once the fault has been rectified, the REF16-S load output is reactivated by an electronic reset signal or manually by pressing the ON/OFF switch directly on the unit.
Key features:l Pluggable into socket 80plus and socket 81plus
- Active linear current limiting
l Capacitive loads up to 20,000µF
l Rated current in fixed amperages 0.09 A...10 A
l Unit plus socket comply with the installation dimensions according to DIN 43880
l Approvals: UL, CSA, GL
l Meets requirements according to NEC Class 2
l OPTION: Control inputs, signalling
Technical details:
operating voltage UB | dC 24 V (18...30 V) |
connection | lINE+ (1) GND (12(b)) |
rated current IN | fixed currents: 0.5 A, 1 A, 2 A, 3 A, 4 A, 6 A, 8 A, 10 A |
quiescent current I0 |
in ON state: typ. 8 mA |
signalling of the operating status via |
- unit switched on load circuit through-controlled Orange: - overload to switch-off Red: - after an overload/short circuit shutdown - short circuit to shutdown - in case of undervoltage in single state - unit switched off via the control input IN+ OFF: - Unit switched off via the ON/OFF switch - Lack of operating voltage
|
load circuit | |
load output | power - MOSFET switching output (plus switching) |
connection | lOAD+ (2) |
overload and short-circuit current cut-off | typ. 1.25 x IN with active current limiting |
switch-off times | see time / current characteristic typ. 80 - 800 ms depending on rated current |
temperature cut-off | internal temperature monitoring with electronic switch-off |
operating voltage monitoring for undervoltage |
oFF: at typ. UB < 14 V ON: at typ. UB > 17 V with automatic OFF and ON switching |
switch-on delay tStart | typ. 2 ms after each switch-on, after reset and after application of UB |
switch-off of the load circuit | electronic switch-off without galvanic isolation |
leakage current in load circuit in OFF state | typ. 1 mA |
capacitive loads | up to 20 000 µF |
free-wheeling circuit | external free-wheeling diode recommended for inductive loads |
parallel connection of several load outputs | not permissible |
Approvals:
Test centre |
Test standard | File Certificate No. |
Rated voltage | Rated current range |
UL | UL 2367 | E306740 | DC 24 V | 0.5 A...10 A |
UL *) | UL 508 CSA C22.2 No. 14 |
E322549 | DC 24 V | 0.5 A...10 A |
CSA *) | CSA C22.2 No.213 (Class I, Division 2, Groups A, B, C, D) |
165971 | DC 24 V | 0.5 A...10 A |
DNV GL |
CG-0339 (classes: temperature, EMC: B; humidity, vibration: A) |
TAE000039W | DC 24 V | 0.5 A...10 A |
*) cULus (listed) and CSA when used
with socket 80plus or socket 81plus
Item name | REF16-S101-DC24V-10A ETA Electronic circuit breaker |
---|---|
SKU | 24-01738 |
Weight | 0.030000 |
Version | 1 ohne galvanische Trennung |
Design: Communication, interface | 01 analog Signal |
Country of manufacture | Germany |
Signal output | 1 signal contact normally open |
Connection type Main connections | P10 flat plug DIN 46244-A6.3-0.8 |
Series | REF16 |
Signal input | 0 without signal input |
Actuating element | W Standard rocker switch |
Undervoltage module | none |
Operating voltage | DC 24 V |
Number of poles | 1-pole thermally protected |
Rated current range | 10A |
Mounting type | S Pluggable |
Characteristic | Medium time-lag tripping characteristic (standard) |
Additional function | 0 ohne |
Traub order number | REF16-S101-DC24V-10A |
Commodity code | 85362010 |
Manufacturer | E-T-A |
Manufacturer number | REF16-S101-DC24V-10A |